If you've ever driven an old truck with manual steering and tires wider than 6.00x16 bias-plies up front, you know where the term "Armstrong power steering" comes from! Even when your bias-ply tires run a little low on air, you gain a great deal of resistance you don't need while trying to maneuver into a spot in the corner store's cozy parking lot to buy a lotto ticket. Let's not even get into doing this with radial tires.
Now you don't need a new truck to flip a U with ease or parallel-park without taking a rest first. Classic Performance Products has just the ticket for the '57-60 Ford F-100 crowd-POWER STEERING! Believe it or not, the cornerstone of their new kit is a compact, relatively light power steering box made by Toyota for only a few years. The Toyota box isn't much bigger than the stock side-steer Gemmer box that came installed in these trucks from the factory. Four-wheel-drive enthusiasts have snatched this box up for years because it easily adapts to confined spaces and it'll turn those big, gnarly mud tires with ease. We might not be driving monster trucks, but we need to turn our tires too, right?
CPP thought so, and they are actually manufacturing their own housings for these since they've become so scarce. That way everyone can buy one, and CPP can come up with more applications to use them in. The Toyota box is topped with a rag joint that attaches directly to the DD shaft in our ididit tilt column-no U-joints hooked to a mess of snaking shafts. We ordered our column in a plain steel finish that we painted black to match our black Lecarra '40 Ford 15-inch steering wheel, but you can order them in chrome or polished to add some sparkle to your interior.
CPP makes things as painless as possible by including a plate to fill the stock hole in the floor that also mounts the bottom column support, a new drag link with tie rod ends, and a pitman arm. They have different power steering hose kits depending on what power steering pump you are using. Call them up and discuss your needs with them if you have questions.
This changeover does require some light fabrication, mostly drilling holes and grinding or filling. There's no welding involved, so most people should be all right; just follow CPP's careful instructions. The guys there really know what's going on since they develop and manufacture most of the parts they sell in-house. About the only thing we couldn't do at this point is wire the ididit column since the truck is currently void of most of its stock wiring, but that's another story-literally.
Read on for the gist of what could be the reason you keep your truck and finally really enjoy it. Then steer yourself in the right direction by calling CPP!
With the old box out and the frame cleaned up, it is time to mark the one new hole you need to mount the Toyota power steering box. Surprisingly, the two rearward original holes line up with the new box's mount. CPP supplies a paper template with the new bolt pattern on it, and with a light on the inside of the frame it's easy to line up with the two original holes like Abel and Jeff are doing here. | 
The light shines through the holes in the frame, so it's a snap to get in the right spot. When it's right, tape it in place. | 
With a center or transfer punch, mark the center of the new front hole according to the template and drill it out to 3/8 inch. |
The pitman arm hole needs to be opened up just a hair. You can do this with a drum sander or even a file if need be; just check that the box fits without any interference. | 
Who doesn't like getting the grinder out? The top edge of the framerail above the pitman arm hole also needs a shave to clear the new box. Again, keep trying until it fits. | 
Here's CPP's machined solid steel mount for the Toyota box. It bolts to the box with the four provided bolts before going into the frame. |
The new box goes in pretty much just like the old one, except you don't have to jimmy a steering shaft back into place since the ididit column will go directly into the rag joint on the steering box. You might also notice the Toyota box's diminutive size; that's why it works so well, and why they're getting hard to find today. The 4x4 guys have been scooping them up for years. CPP is working on manufacturing their own soon. | 
When the box is back in the chassis, the center of the rotation had to be found so the pitman arm could be installed in the 6 o'clock position, which would leave equal rotation to turn left or right. with that taken care of, we put the impact gun on the pitman arm nut and installed the new drag link. Don't forget to put the cotter pins in the castle nuts after they're tightened down! | 
Everything worked out pretty nicely when it was all connected to the steering arm, which was previously heated up and bent down the same amount of drop the CPP dropped axle has to keep the steering geometry correct and avoid bumpsteer. |